Ứng dụng > Chống thấm mái bằng

Flat roofs

Flat roof coverings
1.SURFACE PREPARATION

 NEWTEC PU; NEWTEC-PUA finishes for flat roofs and terraces can be applied on a wide range of existing surfaces (mortar, cement, traditional waterproof sheeting, ceramics, wood etc), using a few simple steps.

2.PRIMER

First apply a coat of primer resin to ensure maximum adhesion to the surface.[NEWTEC-PRIMER]

3.WATERPROOFING LAYER

Depending on the system chosen a membrane from either the NEWTEC PU or NEWTEC PUA range will be used.

4.FINISH LAYER

The NEWTEC-TOPCOAT finishing coat consists of an aliphatic polyurethane resin, highly resistant to UV rays and hard wearing (can be walked on), and to which an anti-slip finish

CERAMIC COVERED TERRACE

After finishing the 3rd waterproofing coating:
For NEWTEC PU product system, about 60-80 minutes after construction, sprinkle or spray completely the surface of the coating with completely dry sand, particle size 0.4 – 0.8mm. This creates a rough surface to bond with the top finish
For NEWTEC PUA product system, it is possible to spray lumpy and apply the finish layer on top immediately

Plot paving
1.SURFACE PREPARATION

 NEWTEC PU; NEWTEC-PUA finishes for flat roofs and terraces can be applied on a wide range of existing surfaces (mortar, cement, traditional waterproof sheeting, ceramics, wood etc), using a few simple steps.

2.PRIMER

First apply a coat of primer resin to ensure maximum adhesion to the surface.[NEWTEC-PRIMER]

3.WATERPROOFING LAYER

Depending on the system chosen a membrane from either the NEWTEC PU or NEWTEC PUA range will be used.

4.FINISH LAYER

The finish of the raised floor will then be positioned directly on the waterproof membrane.

Flat roofs for vehicle trafic
1.SURFACE PREPARATION

 NEWTEC PU; NEWTEC-PUA finishes for flat roofs and terraces can be applied on a wide range of existing surfaces (mortar, cement, traditional waterproof sheeting, ceramics, wood etc), using a few simple steps.

2.PRIMMING

First apply a coat of primer resin to ensure maximum adhesion to the surface.[NEWTEC-PRIMER]

3.WATERPROOFING LAYER

NEWTEC PUA waterproof coating – Polyurea based material will be applied directly on the lining.

4.FINISH LAYER

The NEWTEC-TOPCOAT finishing coat consists of an aliphatic polyurethane resin, highly resistant to UV rays and hard wearing (can be walked on), and to which an anti-slip finish

PU Foam inverted flat roofs
1.SURFACE PREPARATION

 NEWTEC PU; NEWTEC-PUA finishes for flat roofs and terraces can be applied on a wide range of existing surfaces (mortar, cement, traditional waterproof sheeting, ceramics, wood etc), using a few simple steps.

2.PRIMER

First apply a coat of primer resin to ensure maximum adhesion to the surface.[NEWTEC-PRIMER]

3.WATERPROOFING LAYER

Depending on the system chosen a membrane from either the NEWTEC PU or NEWTEC PUA range will be used.

4.Heat-isolation layer

Polystyrene, OPP, XPS, EPS sheets are placed directly on the membrane, careful to ensure they are superimposed on each other, requires correct mounting.

5.Ballast mortar layer

To ensure the correct positioning of polystyrene, OPP, XPS, EPS sheets, these sheets must be ballast, either mortar or dry aggregate can be used.

Garden area foofs & Flooring
1.SURFACE PREPARATION

 NEWTEC PU; NEWTEC-PUA finishes for flat roofs and terraces can be applied on a wide range of existing surfaces (mortar, cement, traditional waterproof sheeting, ceramics, wood etc), using a few simple steps.

2.PRIMER

First apply a coat of primer resin to ensure maximum adhesion to the surface.[NEWTEC-PRIMER]

3.WATERPROOFING LAYER

Depending on the system chosen a membrane from either the NEWTEC PUA range will be used.

4.FINISH LAYER

The finishing part is designed by the Company in charge of the style of the garden roof area.